PDA

View Full Version : Ok i have a lot of questions with pics :)


SS Shaun
06-22-2011, 09:23 PM
ok guys and gals incase you didn't know i am learning about my motor so i took some pictures and questions that i am not sure of.

ok so what is this nut looking thing on the upper control arm
http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5413.jpg

looking at this trans arm does this look right?
http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5414.jpg

ok not sure but i know one is for the throttle cable and one is for the speedo cable right?
http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5409.jpg

wiper motor?
http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5410.jpg

not sure on this one but why is this closed up?
http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5411.jpg

same thing what goes here?
http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5408.jpg

SS Shaun
06-22-2011, 09:24 PM
the other side

http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5405.jpg

http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5402.jpg

and what goes here

http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5407.jpg

SS Shaun
06-22-2011, 09:33 PM
what goes here? i know it runs to the water pump right?
http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5396.jpg

what bolts here right under the intake bolt and over it
http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5395.jpg

what about the two holes next to the water neck
http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5394.jpg

Derek69SS
06-22-2011, 11:18 PM
I'll help with what I can...

Pic #1: I'm guessing that nut had some sort of a screw-in bumpstop as a travel-limiter. Not stock

Pic #3: top hole is throttle cable, lower hole (and adjacent round hole) were plugged on my car from the factory. Speedo cable comes through lower than those holes.

Pic #4: Yes, wiper motor goes there. There is a stamped bracket missing too

Pic #5: The upper plate shouldn't have a hole there... not sure why that's there. The lower (big) plate is covering the holes for the heater & A/C.

Pic #6: Should not be a hole there.

Pic #9: Square hole is where the fuse block goes

SS Shaun
06-23-2011, 07:12 AM
thank you for the info!!

Ms Grumpy
06-23-2011, 08:42 PM
Derek is the man !

SS Shaun
07-01-2011, 10:14 PM
ok what about this?
http://i114.photobucket.com/albums/n271/civiclxb16a/chevelle/IMG_5542-1.jpg

what goes here...lol

Hank70SS
07-02-2011, 06:36 AM
Second set of pictures.

#1, a hose nipple screws in, should look like the one in the back of the water pump. Small piece of hose connect the two.

#2, the 2 standoffs with tapped holes are for mounting a stock type ignition coil.

#3, hole on the right gets another hose nipple screwed in, heater hose goes to it. Other hole is extra, can be used to mount a temp sensor or plugged.

Last pic, is that the rear base of the carb? Vacuum hose to power brake booster.

Ms Grumpy
07-02-2011, 07:39 PM
OK..Hank is the man too..

Derek69SS
07-04-2011, 12:15 AM
Last pic, is that the rear base of the carb? Vacuum hose to power brake booster.
Looks like there's an extra hole in the intake manifold too... put a plug in that hole unless you need it for a vacuum line.

grandsport
07-04-2011, 08:02 AM
Darn,late again missed my chance to be the man.:p

SS Shaun
07-05-2011, 07:55 AM
yeah that hole is for the brake booster which i don't have installed yet i think i am going to try to tackle that this week along with putting the front of the car back on as in bolted on so i can mount the rad in place and get it ready to be started :)

Ms Grumpy
07-05-2011, 06:42 PM
Darn,late again missed my chance to be the man.:p

It's never too late. Keep trying.

Highway Star
07-05-2011, 09:38 PM
Post 1 Pic 5... There used to be parts to a heater core there.
Post 1 Pic 6... Is that a picture of the riveted plate or the square hole in the firewall?
Post 7... Full vacuum port, for brakes or transmission most likely. Looks to be a hole in the intake too. That will need to be tapped/helicoiled/plugged or welded.